We've encountered this article pertaining to A Step-by-Step Guide to Installing a Bathtub listed below on the net and reckoned it made sense to talk about it with you in this article.
Mounting a bathtub isn't precisely rocket science, but it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a new one is also a moderately tough task. If the old tub is readily easily accessible, the task can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also position the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider using one prior to you start. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools and material checklist must make up the following:
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level reviews level.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Activate the water and check all joints and new pipework for leaks and tighten them if essential. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait till the bathtub has been used at least once as this will resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Protect the faucet in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles making use of water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very excited about Tools You Need to Install a New Bathtub and I'm hoping you enjoyed my page. In case you enjoyed reading our page please remember to share it. Thank you so much for taking the time to read it.
Visit